CCS nas been redesigned. This page is part of the old site design and is kept for refference

Home | Components | Istallation | Security | Accessories | Reference | Forum | Directory


IconJava Crossover Calculators

Instructions

  1. Make sure you have Java turned on in your browser.
  2. Enter high and low pass speaker impedances.
  3. Enter desired crossover frequency.
  4. On the second-order crossover calculator you must select type of crossover.
  5. Click on the "calculate" button to get the answers.

Calculators *


First Order (6db/octave) Two-Way Crossover

High Pass Impedance: Ohms
Low Pass Impedance: Ohms
Frequency Hz

                Top of page

6dB Crossover Diagram     C1= F




  L1= mH

  • Phase shift on a first-order crossover is 90 degrees.

 


Second Order (12db/octave) Two-Way Crossover

Linkwitz-Riley Butterworth Bessel

High Pass Impedance: Ohms
Low Pass Impedance: Ohms
Frequency Hz

                Top of page

12dB Crossover Diagram     C1 = F

  L1 = mH


  C2 = F

  L2 = mH

  • Linkwitz-Riley crossovers match attenuation slopes so that system response is flat at crossover point.
  • Butterworth crossovers yield to a peak at the crossover frequency.
  • Bessel crossovers have a frequency response between Linkwitz-Riley and Butterworth crossovers.
  • The phase shift on a second-order crossover is 180 degrees (reversed polarity).

 


Third Order (18db/octave) Two-Way Crossover

High Pass Impedance: Ohms
Low Pass Impedance: Ohms
Frequency Hz

                Top of page

18dB Crossover Diagram     C1 = F
  C2 = F
  L1 = mH

  L2 = mH
  L3 = mH
  C3 = F

  • Phase shift on a third-order crossover is 270 degrees (-90 degrees).

 


Fourth order (24dB/octave) Two-Way Crossover

High Pass Impedance: Ohms
Low Pass Impedance: Ohms
Frequency Hz

                Top of page

24dB Crossover Diagram     C1 = F
  C2 = F
  L1 = mH
  L2 = mH

  C3 = F
  C4 = F
  L3 = mH
  L4 = mH

  • The phase shift on a fourth-order crossover is 360 degrees = 0 degrees (no phase shift).

 


Zobel Circuit (Impedance Stabilization)

DC resistance (Re): Ohms
Inductive Equivalent (Le): Henries

                Top of page

Zobel Circuit Diagram     C1= F


  R1= Ohms

  • Even though speakers are rated at a certain "resistance" (i.e. 4 Ohms), the actual impedance varies with frequency (speakers have inductance). To compensate for the non-linearity of speakers (on mainly subwoofers), Zobel circuits are used.
  • Re is the DC resistance of the woofer (can be measured with an ohmmeter)
  • Le (or Lces) is the electrical inductive equivalent of the driver.

 


L-pad (Speaker Attenuation)

Driver Impedance = Ohms
Desired Attenuation = dB

                Top of page

l-pad.gif (1013 bytes)     R1 = Ohms


  R2 = Ohms

  • An L-pad circuit will attenuate a speaker.
  • L-pads keep the load "seen" by the amplifier constant, affecting only the power delivered to the speaker.  The power delivered by the amplifier remains constant.
  • Since L-pads are made from resistors, it does not induce any phase shifts, or affect frequency response.

* Original calculator design by Speakermania (link will open in new window).

 

Home | Components | Istallation | Security | Accessories | Reference | Forum | Directory